Eyesn1Ce

1. Broadcom Netxtreme Gigabit Ethernet Wireless Drivers For Mac Os
2. Broadcom Netxtreme Gigabit Ethernet Drivers
3. Broadcom Netxtreme Gigabit Ethernet Adapter Driver

From the same iFixit guide, this is your WiFi card. Broadcom BCM4360KML1G 5G WiFi 3-Stream 802.11ac Gigabit Transceiver. You should look at the Bootcamp drivers, because they already have BMC43xx drivers which support 802.11n a/b/g/n/ac. Broadcom NetXtreme Ethernet Controller Driver 17.2.0.2. Broadcom NetXtreme II 1 Gigabit Driver 15.6.0.14 for Windows 32-bit May 24, 2016 Windows (all) 12,039 downloads 473 KB.

• Similar Content

  • By genzai
    

    Hello Mieze,
    Here are the results of my testing:
    First i used an SSDT to inject my i211 and give it the i210 device ID (8086,1533). This appears to be what the driver looks for as it only has an IOPCIPrimaryMatch value in the info plist. after a few tries the SSDT appeared to work and IOJones showed the correct 1533 device ID. The driver did not load however.
    Leaving the SSDT in place i then went about creating a FakePCIID kext. I based it off the 'BCM57XX as BCM57765' kext that is packaged with FakePCIID. Once I got this working, i then saw both network controllers. EN0(i219) and EN2(i210) -- not sure where EN1 went but thats probably not relevant.
    Both controllers showed as loaded everywhere i checked--
    -System Profile showed them both under Ethernet devices, with the proper kexts associated (i211, reported as i210 with AppleIntelI210Ethernet loaded, and i219 with intelMausiEthernet loaded.
    - Network utility showed both devices and EN#
    - DPCImanger showed both devices under its network list
    - IOJones seemed to show both fully loaded with a lot of details under each entry
    - and there was a new entry for 'Ethernet 2' in System Preferences>Network
    However despite all this the i211 port would only show as inactive in system preferences and never showed any sign of life when connected to the network (other than physical LEDs blinking). Furthermore (and very perplexing to me) with I210 'enabled' my i219 controller was also not working. It also showed a red inactive status in network preferences when it should be connected. Another odd thing is that Network Utility seemed to report activity for the i219 (though not the i210) but there was no way to get the OS to otherwise recognize either controller as connected let alone passing traffic.
    Removing the FakePCIID kexts brought my i219 back to life but now i am back to square one.
    Thoughts?
    Thanks!
    g
    
  • By felixaa
    

    Following thread http://www.insanelymac.com/forum/topic/292117-broadcom-bcm57781-how-do-i-patch-the-kext-for-ml-1085/
    was imposible find instructions patterns refered by @Mieze using 'Hopper Disassembler' on AppleBCM5701Ethernet.kext(ver: 10.1.2b3)
    One user on this post: http://www.hackintoshosx.com/files/file/4270-kextstopatch-clover-broadcom-bcm57781-for-yosemite-1010-1012b3/
    claim that is posible patch on-the-fly with Clover but I can´t not find his HEX´s pattern on AppleBCM5701Ethernet binary.
    Any light on this?
    
  • By tanner
    

    I have successfully installed OS X Mavericks onto my Asus Zenbook UX302LA laptop and have almost everything working, except for the following:
    Not Working:
    Wifi( Intel N 7260, Device Instance Path: PCIVEN_8086&DEV_08B1&SUBSYS_C0708086&REV_6B4&33C43F56&0&00E3)
    Two finger scroll
    Touchscreen( Unknown driver)
    Brightness Controls
    Below, I have attached the driver for the N 7260 on Linux, which can possibly be ported to Mac OS X. If the driver cannot be ported, I could add my device ID somehow. If this is all not possible, then I suppose I could use one of my PCIE WIfi cards from another computer.
    Thanks.
    http://wireless.kernel.org/en/users/Drivers/iwlwifi?action=AttachFile&do=get&target=iwlwifi-7260-ucode-22.15.8.0.tgz
    

Broadcom Netxtreme Gigabit Ethernet Wireless Drivers For Mac Os

1. Try updating the driver automatically (Win+X / Device Manager / Network adapter / Double-click on your Broadcom NetXtreme device / Driver tab / Click Update driver) If this doesn't work - i.e. Windows doesn't find a more recent driver. NB: If you already know the exact model of your Broadcom NetXtreme controller you can skip steps 1 and 2.
2. Late 2013 27' iMac. Successfully installed Bootcamp / Windows 10 and it seems as though everything works except Ethernet. Wireless is working. There are no indications of a problem in Device Manager. It lists Broadcom NetXtreme Gigabit Ethernet. I've run the bootcamp driver installer for this model iMac and it finishes with no problem.

Broadcom Netxtreme Gigabit Ethernet Drivers

Broadcom Netxtreme Gigabit Ethernet Adapter Driver